Purchased equipment: boiler of thermal power plant
Location: WUXI China
Telephone: +86 13861509127
E-mail: [email protected]
Contact us for more details about our boilers, solutions and services.

boiler of thermal power plant
Others

Molten salt heaters use molten potassium nitrate and sodium nitrite as heating media. Molten salt heater will heat the powder salt over the melting point until the viscosity of the molten salt allows circulating pump works, after the whole system is under circulating condition, then feed then into the thermal fluid heater for further circulating rising temperature to make it to be recycling used. Normal media working temperature is 400-550℃, top working temperature could reach 600℃.

Technical advantages

Digitized manufacture

  • The laying-off of steel tube adopts CNC 3D laser cutting machine.
  • The manufacture of square coil tube adopts CNC three-dimensional tube bending machine, no forced shaping.
  • The manufacture of serpentuator adopts serpentuator automatic production line, once-forming.

Long life span

  • The optimized radiation heating surface and convective heating surface, the medium flow is more reasonable, without overheat of the carrier and reduce the life;
  • Convection section: optimize convection heating surface and adopt effective fix and structural support to make its working life longer.
  • Set up effective flue gas partition for convection heating surface and cast partition to make it works longer.

Less fuel consumption

  • Use superior refractory brick to build inside and superior perlite in the middle. Keep the furnace temperature under 50℃ to make the minimization of loss.
  • Furnace adopts double close line coil, which makes heating surface sufficient.

Add Comment

What is auxiliary boiler in power plant? - Quo

Once the main plant boiler start producing steam, the package boiler is stopped. The capacity of the Package boiler is very small as compared to the main plant boiler, but it is designed to meet the requirement mentioned above. Hope, it shall serve your purpose.

Preservation & Maintenance Techniques of Boilers i

This article will discuss about Preservation & Maintenance technique of Boilers during shutdown of boiler in thermal power plant. It includes need Boiler Preservation Practices, Boiler Preservation procedures, and Short/Long term preservation.

Type of Boiler in Thermal Power Plant--Z

Type of Boiler in Thermal Power Plant 2016-03-09 10:17:01. We know the thermal power generation plant is the most conventional source of electric power, which offers the driving force for most of the industries. While a boiler or more specifically steam boiler is an essential part of thermal power plant.

Energy integration in boiler section of thermal power pla

In the present work systematic analysis is carried out for retrofitting of boiler section of the conventional thermal power plant of 250 MW capacity with the aim to recover maximum amount of waste heat available in it.

gas boiler for thermal power plant - kodim0604-karawang.c

A thermal power plant is a power plant where steam is used to drive a steam turbine. This turbine is connected to an electrical generator. After this, the water is condensed, and may be used again.

Boiler (Steam Generator) - Coal Fired Power Plan

A boiler or Steam Generator (prime mover) is an integral device in a fossil fuel power plant used to produce steam by applying heat energy to water. A boiler incorporates a furnace in order to burn the fossil fuel (coal, gas, waste etc.) and generate heat which is transferred to water to make steam.

Boiler (power generation) - Wikiped

A boiler or steam generator is a device used to create steam by applying heat energy to water.Although the definitions are somewhat flexible, it can be said that older steam generators were commonly termed boilers and worked at low to medium pressure (7–2,000 kPa or 1–290 psi) but, at pressures above this, it is more usual to speak of a steam generator.

Efficiency of a Coal Fired Boiler in a Typical Therma

The primary units of a coal-fired thermal power plant (Figure-1) are fuel handling system, boiler, turbine and generator and cooling system. The fuel can be in a solid or liquid or gaseous form. Abundantly available coal in India is being used as a solid type of fuel.

Thermal power station - Wikiped

A thermal power station is a power station in which heat energy is converted to electric power. In most of the places in the world the turbine is steam -driven. Water is heated, turns into steam and spins a steam turbine which drives an electrical generator .

Boiler Operation In Thermal Power Plant Pdf - dhl-bolivia.o

Boiler Feedwater Oxygenated Treatment in Power Plants in China. Boiler Feedwater Oxygenated Treatment in Power Plants in China PPC hem PowerPlant Chemistry 2014, 16(5) 295 steam turbine blades is also very common (Figures 5 and 6).

Boiler (Steam Generator) - Coal Fired Power Plan

A boiler or Steam Generator (prime mover) is an integral device in a fossil fuel power plant used to produce steam by applying heat energy to water. A boiler incorporates a furnace in order to burn the fossil fuel (coal, gas, waste etc.) and generate heat which is transferred to water to make steam.

text