Purchased equipment: flue gas temperature 800 degrees 4 tons or 6 tons of boiler
Location: WUXI China
Telephone: +86 13861509127
E-mail: [email protected]
Contact us for more details about our boilers, solutions and services.

flue gas temperature 800 degrees 4 tons or 6 tons of boiler
Others

Molten salt heaters use molten potassium nitrate and sodium nitrite as heating media. Molten salt heater will heat the powder salt over the melting point until the viscosity of the molten salt allows circulating pump works, after the whole system is under circulating condition, then feed then into the thermal fluid heater for further circulating rising temperature to make it to be recycling used. Normal media working temperature is 400-550℃, top working temperature could reach 600℃.

Technical advantages

Digitized manufacture

  • The laying-off of steel tube adopts CNC 3D laser cutting machine.
  • The manufacture of square coil tube adopts CNC three-dimensional tube bending machine, no forced shaping.
  • The manufacture of serpentuator adopts serpentuator automatic production line, once-forming.

Long life span

  • The optimized radiation heating surface and convective heating surface, the medium flow is more reasonable, without overheat of the carrier and reduce the life;
  • Convection section: optimize convection heating surface and adopt effective fix and structural support to make its working life longer.
  • Set up effective flue gas partition for convection heating surface and cast partition to make it works longer.

Less fuel consumption

  • Use superior refractory brick to build inside and superior perlite in the middle. Keep the furnace temperature under 50℃ to make the minimization of loss.
  • Furnace adopts double close line coil, which makes heating surface sufficient.

Add Comment

AM-10-106 An Overview of the FCCU SCR Experience at CITG

An Overview of the FCCU SCR Experience at CITGO’s Lemont Refinery . Presented By: Brian Slemp . Processes Technologist . CITGO Petroleum Corporation . in 2007 with flue gas entering the unit for the first time in early December 2007. The 4 NO + 4 NH3 + O2 Æ 4 N2 + 6 H2O ΔHo = -1,627.7 kJ/mol .

Flue Gas Boiler - zd-boiler.c

The high temperature flue gas generated by waste material or waste liquid flows into the furnace, working medium inside the boiler will take it into the front and end smoke chamber in order, then high temperature flue gas becomes low temperature flue gas, and then discharged into the atmosphere through chimney.

(Cognition practice)

but Wujin materials allowed to run in the 112 degrees below the long-term. 4 turning. Electric Hedge combustion has along the width of the boiler flue gas uniform

testo 340 - Boiler and Burner Kit | Testo, I

With an optional pitot-tube you can also measure the velocity of the flue gas and evaluate the duct and back pass efficiency. By inserting the sampling probe in the flue, the testo 340 will simultaneously calculate mass flow of NOx and CO in lbs/hr or tons/year. Truly your go to instrument for combustion analysis

Optimization of Design Parameter of Rice Parboiling Boil

Optimization of Design Parameter of Rice Parboiling Boiler [6] with a capacity of 7.5 to 16 tons of paddy Simulation results of temperature profile of flue gas Figure 4. Change of

Evaluation of Particulate Emission from a Palm Oil Mill Boiler (Penilaian Perlepasan Zarah daripada Dandang Kilang Minyak Sawi

a sampling port made at the duct of the exiting flue gas between the boiler and a multi-cyclones unit. The results showed obtained in the study which include the average temperature of the flue gas exiting the boiler, flue gas moisture content and boiler capacity, BC was 5.91+4.21, 26.6+18.9 and 19.9+14.2g/kg, respectively.

DHW Biomass Boiler - Leading Biomass Boiler Manufacture

Biomass boiler of DHW series (also called DHW biomass boiler) is the kind of single drum horizontal biomass fired boiler with inclined reciprocating grate, its reciprocating grate’s inclination angle is 15 degrees.

A SURVEY OF EROSION AND CORROSION RESISTANT MATERIALS BEING USED ON BOILER TUBES IN WASTE TO ENERGY BOILE

1293 tons of biomass per day. The bed sand used in a biomass bubbling fluidized bed is very abrasive to the SA-234 in-bed boiler tubes. The tube temperature is approximately 600 degrees F. The flue gas temperature is approximately 1500 degrees F. The burning of the biomass creates chlorides with are very corrosive to the tubes.

Heat regenerator to recover both sensible and heat o

FIGS. 4, 5 and 6 illustrate a simplification of this invention not necessarily requiring the use of rotating rockbeds but rather regeneration of the heat in flue gas to preheat air used for the combustion of the flue gas or preheat boiler feedwater.

Industrial Process Heating - Technology Assessme

37 4. Hybrid process heating technologies. 38 39 These technologies are based upon one or a combination of conduction, convection and radiative heat 40 transfer mechanisms; in practice, conduction/convection dominate lower temperature processes, 41 whereas radiative heat transfer dominates high temperature processes.

2005-Separation of CO2 from Flue Gas A Revie

In addition, it was found that lowering the temperature in the presence of THF by only 6 K increased the mol % of CO2 in hydrate form from 39% to 61%.

text