Purchased equipment: hot water furnace for heating
Location: WUXI China
Telephone: +86 13861509127
E-mail: [email protected]
Contact us for more details about our boilers, solutions and services.

hot water furnace for heating
Others

Molten salt heaters use molten potassium nitrate and sodium nitrite as heating media. Molten salt heater will heat the powder salt over the melting point until the viscosity of the molten salt allows circulating pump works, after the whole system is under circulating condition, then feed then into the thermal fluid heater for further circulating rising temperature to make it to be recycling used. Normal media working temperature is 400-550℃, top working temperature could reach 600℃.

Technical advantages

Digitized manufacture

  • The laying-off of steel tube adopts CNC 3D laser cutting machine.
  • The manufacture of square coil tube adopts CNC three-dimensional tube bending machine, no forced shaping.
  • The manufacture of serpentuator adopts serpentuator automatic production line, once-forming.

Long life span

  • The optimized radiation heating surface and convective heating surface, the medium flow is more reasonable, without overheat of the carrier and reduce the life;
  • Convection section: optimize convection heating surface and adopt effective fix and structural support to make its working life longer.
  • Set up effective flue gas partition for convection heating surface and cast partition to make it works longer.

Less fuel consumption

  • Use superior refractory brick to build inside and superior perlite in the middle. Keep the furnace temperature under 50℃ to make the minimization of loss.
  • Furnace adopts double close line coil, which makes heating surface sufficient.

Add Comment

Rep-Air Heating and Cooling - Furnace and Refrigeratio

Over 50% of energy used in your home comes from HVAC and Hot Water. Picking the right equipment can save you money from the day it is installed. Rebates are sometimes offered to homeowners if energy star rated equipment is installed.

Furnace - Wikiped

A home furnace is a major appliance that is permanently installed to provide heat to an interior space through intermediary fluid movement, which may be air, steam, or hot water. Heating appliances that use steam or hot water as the fluid are normally referred to as a residential steam boiler or residential hot water boiler.

Hot Water Heating Boilers, How to Inspect, Diagnos

Efficiency of Different Heating Methods. The efficiency of hot water heating systems (boilers, or hydronic heat) varies depending on the age and type of equipment, the fuel source (oil or gas for example), and very importantly, the state of tune of the system.

Troubleshooting a Gas-Fired Hot Water Boiler - The Spru

A boiler is a bit more complex than a forced air furnace in that it has more parts, valves, and controls. However, gas-fired boilers are fairly reliable and, when problems do occur, they are usually related to the expansion tank or water circulation pump(s).

NTI GF200 Combi Furnace | All the power you need delivere

NTI manufactures only top-quality hydronic heating equipment. Acknowledged as a leader in research and product development, NTI is a pioneer in developing the most advanced and efficient home heating equipment, including gas boilers, water heaters, combi furnances, hot water tanks and solid fuel boilers.

Forced Hot Water - Heating Systems | Cooling Systems | Oi

Forced Hot Water Heating. This type of system has a boiler for a heat source and heats the water inside the boiler. The heated water is sent up pipes throughout the house by either circulator pumps or zone valves.

Oil-Fired Boilers and Furnaces | Department of Ener

An aquastat controls the temperature of the hot water in a boiler, typically keeping it around 180°F. But when heating needs are lighter in the spring and fall, that's actually higher than needed, and wastes energy. A modulating aquastat, also called an outdoor reset, senses outdoor temperatures and adjusts the hot water temperature accordingly.

Oil-Fired Boilers and Furnaces | Department of Ener

An aquastat controls the temperature of the hot water in a boiler, typically keeping it around 180°F. But when heating needs are lighter in the spring and fall, that's actually higher than needed, and wastes energy. A modulating aquastat, also called an outdoor reset, senses outdoor temperatures and adjusts the hot water temperature accordingly.

Geothermal Heat Pump | WaterFurna

A WaterFurnace geothermal heat pump (or a ground source heat pump) is the most energy efficient, cost effective, and environmentally-friendly way to provide heating and air conditioning. They tap into the solar energy stored in the ground to provide years of reliable, safe home comfort.

Aquaflame Heating and Plumbing - Furnace, Hvac, Heati

furnace, boilers heating, plumbing, furnace, boiler, fire place, hot water tanks, air duct cleaning, heat pumps, Ac,

How to Maintain Hot Water Heating Systems - dummi

This lets air into the pipes which, in turn, makes the water bleed through the system. Turn on the water supply valve so fresh water will flush through the system. The valve is located on the water pipe going into the furnace. When the water stops running, close the drain cock and vents.

text