Purchased equipment: combustion turbine waste heat boiler
Location: WUXI China
Telephone: +86 13861509127
E-mail: [email protected]
Contact us for more details about our boilers, solutions and services.

combustion turbine waste heat boiler
Others

Molten salt heaters use molten potassium nitrate and sodium nitrite as heating media. Molten salt heater will heat the powder salt over the melting point until the viscosity of the molten salt allows circulating pump works, after the whole system is under circulating condition, then feed then into the thermal fluid heater for further circulating rising temperature to make it to be recycling used. Normal media working temperature is 400-550℃, top working temperature could reach 600℃.

Technical advantages

Digitized manufacture

  • The laying-off of steel tube adopts CNC 3D laser cutting machine.
  • The manufacture of square coil tube adopts CNC three-dimensional tube bending machine, no forced shaping.
  • The manufacture of serpentuator adopts serpentuator automatic production line, once-forming.

Long life span

  • The optimized radiation heating surface and convective heating surface, the medium flow is more reasonable, without overheat of the carrier and reduce the life;
  • Convection section: optimize convection heating surface and adopt effective fix and structural support to make its working life longer.
  • Set up effective flue gas partition for convection heating surface and cast partition to make it works longer.

Less fuel consumption

  • Use superior refractory brick to build inside and superior perlite in the middle. Keep the furnace temperature under 50℃ to make the minimization of loss.
  • Furnace adopts double close line coil, which makes heating surface sufficient.

Add Comment

US5623822A - Method of operating a waste-to-energy plan

A waste-to-energy plant which is designed and operated to burn municipal waste (in 2) combines a high pressure steam turbine/generator cycle and a combustion turbine/generator cycle, wherein the exit gas from the combustion turbine (6) is utilized to superheat (in 4) high pressure steam (from 2) prior to entering the steam turbine (8).

Steam Generators and Waste Heat Boilers: For Process an

Steam Generators and Waste Heat Boilers: For Process and Plant Engineers This book begins with basic combustion and boiler efficiency calculations. It then moves on to estimation of furnace exit gas temperature (FEGT), furnace duty, view factors, heat flux, and boiler circulation calculations. Converting Turbine Exhaust Emissions.

Heat recovery steam generator - Wikiped

A heat recovery steam generator (HRSG) is an energy recovery heat exchanger that recovers heat from a hot gas stream. It produces steam that can be used in a process ( cogeneration ) or used to drive a steam turbine ( combined cycle ).

DRAFT PRE-DECISIONAL DRAFT Waste Heat Recovery Technolog

DRAFT – PRE-DECISIONAL – DRAFT 2 23 1. Introduction to the Technology/System 24 1.1. Introduction to Waste Heat Recovery 25 Waste heat in manufacturing is generated from several industrial systems distributed throughout 26 a plant. The largest sources of waste heat for most industries are exhaust and flue gases and

How Gas Turbine Power Plants Work | Department of Ener

A recuperator captures waste heat in the turbine exhaust system to preheat the compressor discharge air before it enters the combustion chamber. A HRSG generates steam by capturing heat from the turbine exhaust. These boilers are also known as heat recovery steam generators.

HRSG Heat Recovery Steam Generator , Gas Combustio

As the working fluid temperature is not high, so the boiler bulky , consumed more than metal.Mainly used for high-temperature waste heat power generation flue gas heat, chemical reaction heat, waste gas, waste heat, less than 200 degrees and so on.

Watertube Waste Heat Boilers for Heat Recovery | E-Tec

Hot flue gasses are passed over the tubes, resulting in rapid boiler response to changes in process conditions. We can configure our water-tube boiler designs for a range of applications, accommodating the dirtiest gas streams (such as those from combustion of solid fuels and waste) to the cleanest (such as turbine exhaust).

Products: Boilers and Turbines | Mitsubishi Heav

Boilers and Turbines. Waste Heat Recovery System(WHRS) Steam Turbine Generators (AT-Type) Auxiliary Boilers . Marine Boiler and Steam Turbine Generator for FPSO/FSO/FSRU/FLNG. Main Boilers and Turbines for Steam Propulsion Vessels (UST) Return to top. Page Top. Footer starts here.

Waste heat recovery - Alfa Lav

fired heaters/furnaces. In both cases, waste heat recovery can lead to substantial fuel savings. Process heat from steam boilers Recovering waste heat often reduces the need for steam in a plant. Consequently the boiler’s fuel consumption is reduced, as are greenhouse gas emissions and the load on the cooling system.

GTA additional combustion systems - saacke.c

A GTA additional combustion system between the turbine and waste heat boiler recycles the residual oxygen in the turbine fuel gas. It improves the fuel efficiency of the plant to more than 96%. The SAACKE portfolio includes:

US5623822A - Method of operating a waste-to-energy plan

A waste-to-energy plant which is designed and operated to burn municipal waste (in 2) combines a high pressure steam turbine/generator cycle and a combustion turbine/generator cycle, wherein the exit gas from the combustion turbine (6) is utilized to superheat (in 4) high pressure steam (from 2) prior to entering the steam turbine (8).

text