Purchased equipment: 1000 kg of steam at a pressure of 16 bar and 0.9 dry is generated by a boiler and it enters the super heater
Location: WUXI China
Telephone: +86 13861509127
E-mail: [email protected]
Contact us for more details about our boilers, solutions and services.

1000 kg of steam at a pressure of 16 bar and 0.9 dry is generated by a boiler and it enters the super heater

Molten salt heaters use molten potassium nitrate and sodium nitrite as heating media. Molten salt heater will heat the powder salt over the melting point until the viscosity of the molten salt allows circulating pump works, after the whole system is under circulating condition, then feed then into the thermal fluid heater for further circulating rising temperature to make it to be recycling used. Normal media working temperature is 400-550℃, top working temperature could reach 600℃.

Technical advantages

Digitized manufacture

  • The laying-off of steel tube adopts CNC 3D laser cutting machine.
  • The manufacture of square coil tube adopts CNC three-dimensional tube bending machine, no forced shaping.
  • The manufacture of serpentuator adopts serpentuator automatic production line, once-forming.

Long life span

  • The optimized radiation heating surface and convective heating surface, the medium flow is more reasonable, without overheat of the carrier and reduce the life;
  • Convection section: optimize convection heating surface and adopt effective fix and structural support to make its working life longer.
  • Set up effective flue gas partition for convection heating surface and cast partition to make it works longer.

Less fuel consumption

  • Use superior refractory brick to build inside and superior perlite in the middle. Keep the furnace temperature under 50℃ to make the minimization of loss.
  • Furnace adopts double close line coil, which makes heating surface sufficient.

Add Comment

(PDF) 9 Superheated Steam Drying - ResearchGa

9 Superheated Steam Drying. (200 0 kg/h, dry basis) novel high-pressure steam flash dryer (25 bar) has. been operated successfully in Finland for drying of.

Power Plant - Tutorial Sheets | Steam Engine | Boil

boiler, cycle and the overall plant are (0.97, 0.95, 0.92, 0.42, and 0.33) respectively. What percentage of the total electricity generated is consumed in running the auxiliaries. Q.4 - A steam generator comprises a boiler, a superheater, an economizer, and an air

Steam Power Plant | Boiler | Power Stati

The superheated steam temperature is about 6000C at a pressure of 30 Mpa(300 kg/cm2) The steam expands in the turbine causing the turbine blades to rotate.14 December 2012 STEAM (THERMAL) POWER PLANT Feed water and steam circuit The superheated steam from the boiler enters the steam turbine.

Steam Capacity Conversion Table | Industrial Contro

Often it is necessary to convert a measure of capacity from one term to another. The conversion table will allow you to quickly convert various measures of capacity. The table and formulas can help you size and pick out components such as condensate pumps and boiler feed pumps. Some additional conversion factors that may prove helpful are shown below.


The easiest way is to imagine a dry kiln as a boiler in reverse. In dry kiln applications, we are kiln at 0 psi (or atmospheric pressure where the saturation temperature is 2120F, or put another way, it has 195° of super- The steam enters the turbine, produces electrical energy,


In well-covered steam mains, the heat lost by radiation when carrying superheated steam is accompanied only by a reduction of the superheat which, if it be sufficiently high at the boiler, will enable a considerable amount of heat to be radiated and still deliver dry or superheated steam to the prime movers.


Steam from a superheater at 7 bar, 300oC is mixed in steady adiabatic flow with wet steam at 7 bar, dryness fraction 0.9. Calculate the mass of wet steam required per kg of superheated steam to produce steam at 7 bar, dry saturated.

High pressure boilers (1) - SlideSha

The steam then enters through the anti priming pipe and flows in the super heater tubes where it is further heated and is finally taken out through the main stop valve and supplied to the Steam turbine or Steam engine when needed. The pressure of steam in case of cross drum boiler may be as high as 100 bar and steaming capacity upto 27000 kg/h

01 Properties of Steam | Steam | Boiler - scribd.c

Problem 8: 1000 kg of steam at a pressure of 16 bar and 0.9 dry is generated by a boiler and it enters the super heater. If the temperature of feed water is 300 C. of Mech & Mfg. Engg. determine a) Total heat added to feed water in the boiler. Dept. 31 .. b) Total heat absorbed in the super heater.

BOILERS | Energy-Models.c

9. Reduction of Boiler Steam Pressure. This is an effective means of reducing fuel consumption, if permissible, by as much as 1 to 2%. Lower steam pressure gives a lower saturated steam temperature and without stack heat recovery, a similar reduction in the temperature of the flue gas temperature results.

Evaluation of synchronous execution of full repowering an

Absolute pressure of the condenser is 0.09 bar . (6) Pressure losses in lines and the equipment are chosen like their catalogues . (7) The isentropic efficiency of the fans and pumps are considered as 82 and 86%, respectively. (8) The efficiency of the generator is considered as 98.45%. (9)