Purchased equipment: selection guide for a boiler at 12bars for coal
Location: WUXI China
Telephone: +86 13861509127
E-mail: [email protected]
Contact us for more details about our boilers, solutions and services.

selection guide for a boiler at 12bars for coal

Molten salt heaters use molten potassium nitrate and sodium nitrite as heating media. Molten salt heater will heat the powder salt over the melting point until the viscosity of the molten salt allows circulating pump works, after the whole system is under circulating condition, then feed then into the thermal fluid heater for further circulating rising temperature to make it to be recycling used. Normal media working temperature is 400-550℃, top working temperature could reach 600℃.

Technical advantages

Digitized manufacture

  • The laying-off of steel tube adopts CNC 3D laser cutting machine.
  • The manufacture of square coil tube adopts CNC three-dimensional tube bending machine, no forced shaping.
  • The manufacture of serpentuator adopts serpentuator automatic production line, once-forming.

Long life span

  • The optimized radiation heating surface and convective heating surface, the medium flow is more reasonable, without overheat of the carrier and reduce the life;
  • Convection section: optimize convection heating surface and adopt effective fix and structural support to make its working life longer.
  • Set up effective flue gas partition for convection heating surface and cast partition to make it works longer.

Less fuel consumption

  • Use superior refractory brick to build inside and superior perlite in the middle. Keep the furnace temperature under 50℃ to make the minimization of loss.
  • Furnace adopts double close line coil, which makes heating surface sufficient.

Add Comment


needed among boiler manufacturers, coal users and coal suppliers. Chemical treatment offers a means of alleviating the problems caused by coal ash deposits. Treatment of oil has been accepted for a number of years(l), but only occasional successes have been reported for coal (2-6).

Guide to Low-Emission Boiler and Combustion Equipmen

GUIDE TO LOW-EMISSION BOILER AND COMBUSTION EQUIPMENT SELECTION C. B. Oland Date Published: April 2002 Prepared for the U.S. Department of Energy Office of Industrial Technologies Prepared by OAK RIDGE NATIONAL LABORATORY Oak Ridge, Tennessee 37831 managed by UT-BATTELLE, LLC for the U.S. DEPARTMENT OF ENERGY under contract DE-AC05-00OR22725

Guide to Low-Emission Boiler and Combustion Equipmen

ORNL/TM-2002/19 GUIDE TO LOW-EMISSION BOILER AND COMBUSTION EQUIPMENT SELECTION C. B. Oland Date Published: April 2002 Prepared for the U.S. Department of Energy

A planner's guide for selecting clean-coal technologie

A planner's guide for selecting clean-coal technologies for power plants (English) Abstract. This report has been prepared as a technology selection guide for the use of power system planners and engineers to facilitate the selection of cost-effective, environmentally friendly technologies for coal-based power generation in countries grappling

Refractory Selection Guide for Coal Fired Boile

To ensure long service life and high overall operational efficiency of coal fired boilers, it is necessary to select appropriate refractory. ANH Refractories offers a range of solutions and a refractory selection guide is provided herein.

Guide to Low-Emission Boiler and Combustion Equipment Selecti

Boiler owners and operators who need additional generating capacity face a number of legal, political, environmental, economic, and technical challenges. Their key to success requires selection of an adequately sized low-emission boiler and combustion equipment that can be operated in compliance


power plants maximum requirements of fuel is a coal. The handling of this fuel is a great job. To handle the fuel, i.e., coal, each power station is equipped with a coal handling plant. Maintenance of Critical Equipments for Coal Handling Plants (CHP) of Thermal Power Stations is typical job.

Boilers of the product-line R22 G.P R22/22, R22/40, R22/6

24 12) BOILER HOUSE SPACE REQUIREMENT All boilers can be placed directly onto hard level ground. No boiler plinth is required as the high grade plastic condenser is located on the low part of the boiler. The noise level emanating from the boilers is below 72 dba.

Steam Boilers Selection Guidelines - Chromalox, In

Boiler selection is usually based on the operating pressure (psig) and steaming capacity (Lbs/Hr). When the pressure or temperature and kilowatt rating or Lbs./Hr. of steam requirements are known, the recommended boiler can be determined from the following Boiler Selection Chart.

Steelworker Vol. 2 - 14251 - [PDF Documen

NONRESIDENT TRAINING COURSE November 1996 Steelworker, Volume 2 NAVEDTRA 14251 DISTRIBUTION STATEMENT A: Approved for public release; distribution is unlimited. Although

coal consumption for a 12ton boiler - ugcnetnic.

2018-10-23 Coal consumption calculation of circulating fluidized bed boiler is related to fuel and design efficiency. how much coal consumption of the CFB boiler per day is conducive to the customer's boiler selection, provide convenient conditions for customer to reserve fuel.