Purchased equipment: design of boiler of thermal power station
Location: WUXI China
Telephone: +86 13861509127
E-mail: [email protected]
Contact us for more details about our boilers, solutions and services.

design of boiler of thermal power station
Others

Molten salt heaters use molten potassium nitrate and sodium nitrite as heating media. Molten salt heater will heat the powder salt over the melting point until the viscosity of the molten salt allows circulating pump works, after the whole system is under circulating condition, then feed then into the thermal fluid heater for further circulating rising temperature to make it to be recycling used. Normal media working temperature is 400-550℃, top working temperature could reach 600℃.

Technical advantages

Digitized manufacture

  • The laying-off of steel tube adopts CNC 3D laser cutting machine.
  • The manufacture of square coil tube adopts CNC three-dimensional tube bending machine, no forced shaping.
  • The manufacture of serpentuator adopts serpentuator automatic production line, once-forming.

Long life span

  • The optimized radiation heating surface and convective heating surface, the medium flow is more reasonable, without overheat of the carrier and reduce the life;
  • Convection section: optimize convection heating surface and adopt effective fix and structural support to make its working life longer.
  • Set up effective flue gas partition for convection heating surface and cast partition to make it works longer.

Less fuel consumption

  • Use superior refractory brick to build inside and superior perlite in the middle. Keep the furnace temperature under 50℃ to make the minimization of loss.
  • Furnace adopts double close line coil, which makes heating surface sufficient.

Add Comment

Design and modeling of low temperature solar thermal powe

A solar thermal power plant based on Kalina power system has been modeled thermodynamically and analyzed parametrically. The performance of the plant has been studied at the separator temperature of 110–150 °C, strong solution concentration of 0.65–0.8, turbine inlet concentration of 0.92–0.955 and solar beam radiation of 400–700 W/m 2 .

PLC & SCADA Based Effective Boiler Automation System fo

boiler automation to monitor and control the boiler temperature, pressure and water level in thermal power plant. III. NEED FOR BOILER AUTOMATION Boiler is one of the most important parts in any power plant. Which require continuous monitoring and inspection at frequent interval. In Power plants it has number of boiling section.

Power Generation Energy Efficient Design of Auxiliar

− A subset of BoP that encompasses drive power components such as pumps, fans, motors and their power electronics such as variable-frequency drives. These provide drive power for fuel handling, furnace draft, and feedwater pumping. These systems and components will be referred to as ‘Drivepower’.

Operation and maintenance schedule of a steam turbin

classification of the power plant, existing power plants, location and their generated power in Nigeria. A thermal power station is a power plant in which the prime mover is steam driven. Water is heated, turns into steam and spins a steam turbine which drives an electrical generator.

Design Features and Commissioning of the 700 MW Coal-Fire

Thermal Power Station No.2 was designed based on the high-performance and reliable 500 MW boiler at the same Power Station No.1. Applying elevated steam of 593/593 O C, our state-of-the-art low-NOx combustion A-

Thermal power station - Wikiped

A thermal power station is a power station in which heat energy is converted to electric power. In most of the places in the world the turbine is steam-driven. Water is heated, turns into steam and spins a steam turbine which drives an electrical generator.

Layout of Thermal Power Plant | Boiler | Power Stati

Thermal Power Plants constitute 75.43% of the total installed captive and non-captive power generation in India. In thermal generating stations coal, oil, natural gas, etc are employed as primary sources of energy. Diagram of a typical coal-fired thermal power station Diagram of a typical coal-fired thermal power station 1. Cooling tower 2.

Design and modeling of low temperature solar thermal powe

A solar thermal power plant based on Kalina power system has been modeled thermodynamically and analyzed parametrically. The performance of the plant has been studied at the separator temperature of 110–150 °C, strong solution concentration of 0.65–0.8, turbine inlet concentration of 0.92–0.955 and solar beam radiation of 400–700 W/m 2 .

Condition Based Monitoring of boiler parameters in

This contributes to reduced boiler efficiency and increased in down time on the boiler which has impacted on the total output of the station. 1.1. Clinker Formation Clinkering is the formation of non-combustible residue that is fused into an irregular lump that remains after combustion of coal [3].

Thermal Power Station | Boiler | Steam Engi

A thermal power station is a power plant in which the prime mover is steam driven. Water is heated, turns into steam and spins a steam turbine which drives an electrical generator. After it passes through the turbine, the steam is condensed in a condenser; this is known as a Rankine cycle.

by Flemming Skovgaard Nielsen, BWE Paolo Danesi, BWE M.

Modern boiler design 2012 This article is BWE property and subject to copyright protection. 3 | P a g e 1. Abstract Introducing modern boiler concepts in the design of thermal power stations is nowadays becoming mandatory, not only from an economic point of view of new investments, but also as a

text